| 表干时间 | 12 |
|---|---|
| 材质 | 见说明 |
| 产地 | 山东 |
| 储存期 | 见包装 |
| 耗漆量 | 2.2—2.3（㎡/kg） |
| 耐碱性 | 合格 |
| 耐水性 | 0.3Mpa |
| 外观 | 桶装 |
| 用途范围 | 广泛 |
| 漆膜颜色 | 见包装 |
| 品牌 | 盾源 |
| 液态类型 | 水乳型 |
供应盾源 彩色双组份聚氨酯防水涂料 产品类型
本产品为双组份反应固化型防水涂料，产品分为黑色沥青和彩色环保型两种。
产品指标
（1）主要技术指标：招待JC/T500-92（96）标准
（2）拉伸强度≥1.65MP a
（3）断裂延伸率≥350%
低温柔性：－30℃±1℃2h无裂纹
不透水性：0.3 MP a30min无渗漏?
适用时间：≥20min
固化时间：表干≤4h 实干≤12h?
固含量：≥94% 性能特点
本产品属双组份反应型胶体防水涂料，常温固化后形成富有弹性的整体化橡胶状的防水层，常温施工，工艺简便，性能可靠，无接缝，耐热耐寒，耐油耐磨，耐腐蚀、耐老化，粘结强度高，延伸性能好，溶于油脂不溶于水，可与水泥、滑石粉填充料混合使用。
产品用途
1、可用于混凝土斜屋面、天沟、雨蓬及各种不规则开关屋面做防水层。
2、可用于地下工程、内外墙、地坪、厨浴间、游泳池等工程的防水、防漏。
3、可用于金属航空航天工业部与混凝土接缝，混凝土构件缝密封防水。
4、其它防水，防腐，粘结。
使用方法
将甲组份（透明液）和乙组份（黑色液/彩色液）按1：2或1：1.5的重量比例午后倒入清洁干燥容器内，搅拌三分钟，使二份混合均匀，即可涂刷于需施工部位，并要求在半小时内完成，可取得**效果，施工环境温度0℃以上，施工涂刷2mm以下的分二次进行**次涂刷用料为30%，第二次将余料用尽。施工厚度要求在2m以上的分三次涂刷，每次用料1/3。
Supply 盾源 color polyurethane waterproof coatingProduct types
This product is a two-component curing type waterproof coating, products are divided into the pitch black and color environmental protection type two.
The product index
(1) the main technical indexes: JC/T500-92 (96) standard.
(2) the tensile strength is more than or equal to 1.65MP a
(3) the fracture elongation ≥ 350%
Low temperature flexible: 30 ± 1 ℃ 2H no crack
Impervious: 0.3 MP a30min no leakage for time: ≥ 20min
This product is a two - component reaction type colloidal waterproof coating, waterproof layer, room temperature curing after the formation of the whole rubber like elastic room construction, simple process, reliable performance, no seams, heat resistant, oil resistant and wear resistant, corrosion resistance, aging resistance, high adhesive strength, good extension performance, soluble in oil insoluble in water, and cement, talc filler mixed use.
Product use
1, can be used for concrete sloping roof, gutters, canopy and various irregular switch roof waterproofing. 1, can be used for concrete sloping roof, gutters, canopy and various irregular switch roof waterproofing.
2, can be used in underground engineering, internal and external wall, floor, kitchen and bathroom, a swimming pool and other engineering waterproof, leakproof.
3, can be used for metal aerospace industry and concrete joints, waterproof concrete joint.
3, can be used for metal aerospace industry and concrete joints, waterproof concrete joint.
4, other waterproof, **-corrosion, bond.
Using the methods of component a (transparent liquid) and B (black liquid / color liquid) afternoon press 1:2 or 1:1.5 weight ratio into a clean and dry container, stirring for three minutes, the two mixed evenly, can besmear to construction site, and in half an hour, can achieve the best results, the construction of environment temperature above 0 ℃, construction brushing 2mm below two times, the first coating materials used for the 30%, second times more than makings exhaustion. The thickness of the construction requirements in three populations of 2m or above, each material 1/3.